Skip to product information
1 of 11
Hearts and Scrolls Santa Mail Mailbox Sticker Pack

Prefer not to paint?

Hearts and Scrolls Santa Mail Mailbox Sticker Pack

The matching sticker pack colors every layer. Stick the printed sheets on your wood, line the laser up on the crosshairs and cut with the sticker on.

The first button puts the sticker pack and this cut file in your cart together: no need to add the cut file again.

Hearts and Scrolls Santa Mail Mailbox Laser Cut File

Hearts and Scrolls Santa Mail Mailbox Laser Cut File

Instant digital downloadSVG, DXF, PDF, AI7 x 4 x 9 in52 pieces

$5.54$13.85 60% off

Hearts and Scrolls Santa Mail Mailbox: a box cut file from MEJA Design Studio, drawn to be cut on your own laser from 1/8 in plywood.

This is a digital file. Nothing is shipped. You cut the mailbox yourself from two 12 x 20 in sheets of 1/8 in (3 mm) plywood.

What you get (instant digital download, one zip)

  • The cut files in SVG, DXF, PDF and AI formats: two 12 x 20 in sheets, one file for each sheet in each format
  • Assembly guide (PDF): every part by name and number, the sizes, what you need and the steps, numbered, with drawings
  • A picture of the mailbox closed, a picture of it open and a picture of the parts
  • START_HERE and your license

Details

  • Size: 9 in tall on its post and base. The body is 7 in long, 4 in wide and 5 in tall; the base is 6 in across
  • 52 parts, all cut from 1/8 in (3 mm) plywood: two arched ends (a back plate and a front frame), two side walls, the floor, nine slats for the round top, the door and its two-disc knob, the flag with its cap, peg and stop, two crossed post plates (each cut twice and glued double) and two base discs, 18 letters and 4 scrolls cut loose (a set for each side wall), and a lining glued inside the back plate, the frame and the door
  • The words: SANTA MAIL on both side walls, in raised capitals 0.66 in tall, a scroll to each side of them
  • The door turns down and forward on two wooden pins and hangs open a little past level. Shut, it is held by the fit of its pins alone: there is no catch. It opens about 98 degrees.
  • The flag turns on a square wooden peg under a round cap; a second peg stops it level, and upright
  • The walls, the floor and the slats end in tabs that go through slots in the two arched ends: every joint presses together by hand, and glue holds it
  • Made for 1/8 in (3 mm) plywood ONLY: every tab and slot is sized for that thickness. Do not resize the file: resizing changes the fit.
  • Red lines = cut. Blue lines = light marks (the outline of every raised letter and scroll on the two side walls: each is glued on its outline; the ring near the door's top, where the knob is glued; the fine lines of the design (petals, veins, leaves)): score or engrave them lightly, they never cut through. Part names are written as notes and are never cut.
  • Sold unfinished: the first picture shows the mailbox painted, the second as it is cut. Leave the wood bare, stain it, or paint it by hand. Paint and stain are not part of this file.

You supply

  • Two 12 x 20 in sheets of 1/8 in (3 mm) plywood
  • Wood glue
  • Tape, to hold the body together while the glue sets
  • Paint, if you like (the first picture shows the whole mailbox painted): paint the letters, the scrolls and the flag before you glue them on

Prefer not to paint?

A matching printed sticker pack is available in our store: https://mejadesigns.com/products/hearts-and-scrolls-santa-mail-mailbox-1-sticker-pack. You stick each printed sheet on your plywood, line the laser up on its crosshairs and cut wood and sticker together: 49 parts come out colored, on the faces that show.

Please note

  • The door and the back plate are pierced right through: what is in the mailbox shows through them. The side walls and the round top are solid.
  • The door stays shut by the fit of its pins alone: there is no catch.
  • The door is hung WHILE the mailbox is built: its two pins go into the eyes of the side walls' two ears as the front frame is slid on. It cannot be put in afterwards. The guide says so at the step where it matters.
  • It is a table-top decoration, 9 in tall: not a mailbox for outdoors.
  • This is a DIGITAL file. No physical item is shipped.
  • You need a laser cutter and basic knowledge of your machine's software.
  • Plywood sold as 1/8 in varies a little in thickness: dry fit the parts before gluing.
  • Fine fretwork and small letters: use good, flat plywood, and lift the parts off the bed with care.

Works with

Glowforge, xTool, LightBurn, OMTech, Epilog, Trotec, Thunder and any software that opens SVG, DXF, PDF or AI.

License

Limited commercial license included: you may sell up to 200 finished items you make from each design. Sharing, reselling or redistributing the digital files is not permitted.

Questions? Message me any time - happy to help.

How the download works

Right after checkout your download link is on the order page, and it is emailed to you as well. The download is one zip that holds every file listed above. Nothing is shipped.

Which machines it works with

Any laser whose software opens SVG, DXF, PDF or AI: Glowforge, xTool, LightBurn machines, OMTech, Epilog, Trotec and others. Designs are made for 1/8 in (3 mm) material.

View full details